|Boost Gauge The all NEW advanced Boost Gauge is finally here!!!
T.M.WORKS Boost Gauge is a turbo pressure boost gauge where signal of the pressure is directly picked up from the sensor itself (usually Intake Manifold Pressure Sensor; some vehicle models might be picked up from Turbocharger Boost Pressure Sensor).
After installation of an external chiptuning, boost gauge with OBDII connection will not display an accurate figure as values from the OBDII are usually calculated.
T.M.WORKS Boost Gauge can display a more accurate value to the gauge as it is connected directly to the sensor at the vehicle's engine.
Also, recent modern engines, it is almost impossible to install a conventional type boost gauge. This is because, there is no place where we can tap at the intake manifold to extract the pressure. We might need additional items such as adapters (T-junction type) and additoinal pressure hoses etc. to get it installed. This makes the engine compartment looks messy with additional hoses installed or used.
For example, in the case of Suzuki Alto Works HA36S, even with a T-junction type adapter installed to the boost pressure solenoid valve, the boost pressure value shown might still not be accurate. With T.M.WORKS Boost Gauge, no additional adapters or pressure hoses are needed. By having the correct connector that matches the sensor, directly picking up signal from the Turbocharger Boost Pressure Sensor or Intake Manifold Pressure Sensor, this will be the most accurate method to measure the boost pressure value.
For installation, specific wiring harness kit and air vent adapter (for some car models only) will be available for specific car models.
T.M.WORKS Boost Gauge
☆：No additional sensor needed (used in conventional gauges).
☆：Special coated lens.
☆：Overboost warning be set (with alarm function).
☆：LCD technology display to ensure good visibility.
☆：Backlight illumination adjustment function
(orange or white backlight illumination can be selected).
☆: Peak boost pressure hold mode.
☆：Compatible for gasoline/petrol and diesel car models.
☆：Easy installation with specific wiring harness kit for specific
☆：Air vent adapter available (for some car models only).
2.0kPa Model No. BG001 ￥18,000 (excluding tax)
2.5kPa Model No. BG002￥20,000 (excluding tax)
T.M.WORKS RGB Boost Gauge
☆：Value of voltage, water temperature and intake manifold air
temperature can be displayed via OBDII port connection
☆：No additional sensor needed (used in conventional gauges)
☆：Special coated lens
☆：Overboost warning be set (with alarm function)
☆：LCD technology display to ensure good visibility
Backlight illumination adjustment function
illumination can be selected)
☆：Peak boost pressure hold mode
☆：Compatible for gasoline/petrol and diesel car models
☆：Easy installation with specific wiring harness kit for specific car
☆：Air vent adapter available (for some car models only)
2.0kPa Model No. RGB01 ￥32,000 (excluding tax)
Easy Plug n Play installation with wiring harnes kit dedicated to specific vehicle models.
①Open the front hood. Lock all doors and leave it for at least 15 minutes.
②Remove the intake manifold pressure sensor connector.
③Connect it with the supplied harness from T.M.WORKS Boost Gauge.
④Pull the yellow wiring harness into the car's interior.
⑤Follow the installation manual provided for the in-car wiring procedures.
⑥Set T.M.WORKS Boost Gauge.
⑦Perform gauge "Zero" calibration according to the installation manual.
⑧Once done, start the engine and monitor.
Specific wiring harness kit from ￥2,500 (excluding tax)
Air Vent Gauge Adapter(compatible car models)
AUDI A3 8P.
AUDI TT 8N
VW GOLF MK6
MERCEDES BENZ A SERIES
MERCEDES BENZ GLA SERIES
SMART 453 0.9Turbo
TOYOTA PRIUS C
FORD FIESTA MKVII
FORD MONDEO 2007~2013
Copyright © T.M.WORKS, Ltd. All rights reserved.